Lime filler for repairing existing internal surfaces, available in two different grades:

• 1 kg (Fine) – Suitable for hairline cracks
• 1 kg (Coarse) – Suitable for dents in existing plaster

Deeper/larger holes or patching in should be done using premixed lime mortar.

The post Lime Filler appeared first on Eden Hot Lime Mortar.

Made in Cumbria, our lime plaster (Eden Skim Coat) is produced via the hot mix method. Mixed at ratio of 2:1 (sand:quicklime).

Lime plaster is a traditional internal finishing plaster, applied over base coats of lime mortar or insulated lime. Can also be used for skimming onto plasterboard, for this the boards would need to be primed first with Baumit Premium Primer (DG27).

The lime plaster should be applied at less than 2mm coats at anyone time, a second pass can be done 2-3 hours later (this depends on temperature and humidity in the room)

Coverage:

22kg bucket covers approximately 4-5m² (allowing for 2 x 2mm passes)

The post Lime Plaster (Skim) appeared first on Eden Hot Lime Mortar.

Made in Cumbria, our lime mortar is produced via the dry slaked hot mix method. Mixed at ratio of 3:1 (sand:quicklime) and supplied unhaired.

The lime mortar is used for backing coats of lime plaster and lime render, scratch coats will need hair or fibres adding to the mix when knocking the mortar back up for reinforcement. Also used for internal and external building/bedding, pointing and parging/torching (add a Pozzolan for external use or damp internal conditions).

For internal final finish see Lime Plaster (Eden Skim Coat).

Lime Mortar Colour Options (for pointing)

Three colour options are available as premixed lime mortars, these would just need to be knocked up before use and pozzolan added if needed:

• 1 Eden Standard – Nosterfield sharp sand and -3mm kibble quicklime
• 2 Eden Fine Yellow – Appleton Yellow sand blended with limestone dust and -3mm kibble quicklime
• 3 Eden Fine Red – Red plastering sand blended with limestone dust and -3mm kibble quicklime

Colour Examples

                     1 Eden Standard                                        2 Eden Fine Yellow                                       3 Eden Fine Red

Lime Mortar Coverage:

• Render/plaster scratch coats @15mm thick = 39kg/m²
• Render/plaster float coats @10mm thick = 26kg/m²
• Re-pointing stonework = Approximately 26kg/m²
• Re-pointing brickwork (assuming 10mm wide x 20mm deep joint) = Approximately 8kg/m² (including 10% waste)
• Brick laying – 1000kg of mortar will lay 900-1000 bricks (no waste allowed)
• Stone bedding – 1000kg of mortar will bed approximately 5 m³ of stone
• Roof parging/torching – Approximately 22kg of lime mortar (dependent on slate & lath).

Pozzolan

Argical-M 1000 Pozzolan is helpful when applying hot lime mixes in damp, frost prone or exposed locations. The addition of Argical to hot lime mixes will increase compressive strength which helps to offer additional protection during the carbonation period.
Traditionally, volcanic ash, brick dust and other forms of burnt clays were used as additives in hot lime mixes and today this is refined in the form of Argical-M 1000. The term ‘pozzolan’ originates from the Italian town of Pozzuoli where volcanic ash was added during Roman times.

We recommend adding a pozzolan between 5% – 10% by volume depending on the time of year, exposure and use.

Quantity required for gauging into pre-mixed mortars:

• 5% by volume (1/20) – One tonne of mortar requires 12.5kg of Argical-M 1000
• 10% by volume (1/10) – One tonne of mortar requires 25kg of Argical-M 1000

Quantity required when making hot mix mortars on site:

• 5% by volume – For every measure of Quicklime added to the mix, add approx 20% of the same measure of Argical-M 1000
• 10% by volume – For every measure of Quicklime added to the mix, add approx 40% of the same measure of Argical-M 1000

The post Lime Mortar appeared first on Eden Hot Lime Mortar.

The Eden Pointing Tool/Slicker is purpose-built for precision repointing with lime mortars and heritage materials. Each dual-ended tool is crafted from 3mm stainless steel, offering excellent corrosion resistance and a smooth, reliable finish across a range of joint widths.
Available in three size combinations:
• 8mm / 12mm
• 10mm / 14mm
• 16mm / 19mm

Also available as a complete set of three, giving you full flexibility across restoration projects and traditional masonry detailing.
Whether you’re working on historic stonework or fresh lime mortar joints, this pointing tool/slicker delivers clean lines, comfortable handling, and long-lasting performance.

• Dual-ended for versatility
• Durable stainless steel construction
• Ideal for lime mortar and conservation work
• Built to last. Engineered for heritage.

Nylon Churn Brush

Churn brushes are used for finishing lime pointing, the lime pointing should not be left with a smooth trowel finish. Brush and beat the pointing firmly, this will seal and shrinkage cracks and open the surface of the pointing allow it to carbonate.

The post Pointing Tools appeared first on Eden Hot Lime Mortar.

The Tyre Rubber 30L tub is made from recycled tyres and is heavy duty, strong, flexible and long-lasting. It’s still one of the few products to make use of used tyres, which are particularly difficult to recycle because the rubber is vulcanised. They are pressed it to make incredibly durable, hard wearing and flexible equipment that is perfect for all of the heavy duty jobs you can throw at it!

Tyre Rubber Tubs from Eden Hot Lime Mortar ARE suitable for use with high-temperature materials, INCLUDING hot lime.

When it comes to tubs, there isn’t a better quality tub on the market than the Tyre Rubber Tub. Ergonomic design and the most sophisticated production facility all highlight the commitment to quality.

Made from recycled tyres and with a heavy duty construction, this is an ideal basket for working on site or animals, whether it’s indoors or outdoors.

Both flexible and strong it won’t get damaged easily and the 30L volume makes it perfect for a wide range of applications.

Tyre Rubber Tub Key Features:

• Strong & Durable
• Recycled Tyre Rubber
• Frost & UV Proof
• Pet Safe
• Flexible Sides

Use for:

Building & plastering, mixing lime including hot lime, plumbing & electrics, carrying, mixing, washing, cleaning & just about anything else!

The post Tyre Rubber Tub appeared first on Eden Hot Lime Mortar.

Insulating lime plaster is a breathable insulation which can be applied directly on to the interior external walls as well as internal walls. The insulation is applied in a wet form, normally with the aid of a harling trowel, but some builders use a conventional float. The insulation can be built up in layers, at a maximum of 20-25mm at any one point, once dry another layer can then be applied.
The first coat can be left quite rough as it will aid the cohesion of the following layer. The second layer can be smoothed off an hour or two later so the skim coat will be easier to apply.

Generally people tend to apply a 50mm backing coat plus a 2-4mm skim coat, followed by a lime wash finish. It has been known for some architects to specify 100mm in four coats, but from feedback that we are receiving, 50mm is achieving some wonderful results.

46mm of insulating lime plaster has a Thermal conductivity (Lamda Value) 0.113 W/(mK)
Results c/o National Physical Laboratory specimen QM398 reference: 2010120038/1

Health & Safety Information

• Eye protection must be worn at all times
• It is advisable to wear gloves- nitrile/ latex are desirable
• Masks are advisable when taking materials out of the bag

Mixing of the Insulation

The materials for the insulation come in three separate bags. The materials can be mixed in a paddle mixer (preferable as less splashback) or a belle mixer. The contents require a thorough mix (15-20 mins) before application. The walls need to have been brushed down of any loose materials then given a wash down half an hour before applying the first layer. The second layer is generally applied a week later once the first layer has dried (turned white), this depends on the temperature/humidity and how dry the walls are. Before applying the second layer the first layer should be dampened.

Read more about our lime insulation, and the customer reviews in our FAQ Why Use Insulated Lime Plaster

The post Insulating Lime Plaster appeared first on Eden Hot Lime Mortar.

Forced action mixers are an essential piece of equipment for any site. By ensuring that the materials are thoroughly mixed, forced action mixers help to create a consistent, high-quality finished product. With a forced action mixer from Baron, you get the best of both worlds – power and performance in one simple design. The variable speed control allows for personalized mixing needs while still providing enough torque to tackle any job that comes your way!
Whether you are a professional contractor or a DIY enthusiast, forced action mixers can help you achieve superior results. With their help, you can create beautiful, long-lasting surfaces that will stand up to the elements and look great for years to come.

E120 forced action mixer – 2.0kW 1x240V

This robust and efficient forced action mixer has many advantages. Its large 2.0 kW powerful maintenance-free motor, strong frame and good ergonomics make it a great choice.
• Rubber wheels for higher comfort.
• Tight and robust opening system.
• Positioning bolt prevents unintended cover closure.
• Easily interchangeable mixer head.
• Easy to clean and easy to maintain.

E200 forced action mixer – (110V)

This model has a mixing capacity of 160 litres and a weight of 180kg, so it is ideal for medium-large resin mixes. 200 litre drum capacity, 160 litre /150kg / 6 bags mixing capacity
• Large and robust 2.2kW motor
• Can be used by one man
• Optimum mixing capacity and handling
• Security protection at the outlet
• Easy to clean and maintain
• Easily loaded

Mixers are expected to be returned cleaned and in the condition as they left, cleaning and damage charges will apply.

The post Mixer Hire appeared first on Eden Hot Lime Mortar.

The geotextile membrane is used for separation layers on Limecrete floors that incorporate GEOCELL foam glass aggregate. This is positioned onto the sub-soil bellow the foam glass, then a second layer over the top once the foam glass is compacted.

Available Sizes
100m roll x 4.5m wide
1m unit x 4.5m wide (supplied by the running metre)

Other Uses
MultiTrack is a thermally bonded or needle punched non-woven geotextile that offers many benefits where separation, filtration and drainage functions are required.
It delivers excellent durability and drainage function in addition to its very high water flow capability, but reduced strength in comparison to a woven geotextile. It can also be used for erosion control and protect membranes from being punctured. Ideal for roads, car parks, coastal defences and drainage systems.

Separating/strengthening layer under access roads and areas of hard standing
Filter surround for trench drains
Separation to stop the intermixing of dissimilar soil layers
Filtration – allowing the flow of water whilst preventing the passage of soil
Horse arenas – separation of infill materials
Filter surround for infiltration tanks

The post Geotextile Membrane appeared first on Eden Hot Lime Mortar.

Biaxial Geogrid is used for attaching underfloor heating pipes on Limecrete floors that incorporate GEOCELL foam glass aggregate.

Available Sizes
50m roll x 4m wide
1m unit x 2m wide (supplied by the running metre)

The Geogrid is laid out over the Geotextile membrane that is wrapped around the compacted GEOCELL foam glass aggregate. The Geogrid can then be used to secure the underfloor heating pipe with either clip rails or cable ties to secure the pipes in place before the screed is installed.

The post Biaxial Geogrid appeared first on Eden Hot Lime Mortar.

Render mesh is used to reinforce plasters and renders to minimise the likelihood of shrinkage or movement cracks. It can be applied across vulnerable joints and corners of windows, doors and across the whole surface of newly rendered or plastered walls.

When applying backing coat plasters onto carrier boards like Woodfibre or Wood Wool boards it’s advised to “sandwich” the render mesh into the backing coat. This will reinforce the plaster to minimise the chance of shrinkage or movement cracks at the joints of the carrier boards.

Available in either 160gm or 145gm
4 mm mesh (160gm) – 50m x 1.0 m
10 mm mesh (145gm) – 50m x 1.0 m
Also supplied by the running metre

Render mesh for thin coat plaster and render systems tends to be the 4mm (160gm), when reinforcing thicker traditional types of mortar the 10mm (145gm) is used.

• Ideal for reinforcing external render particularly around openings or areas of traditional weakness.
• It can be used to stabilise unstable surfaces, as well as cover and help prevent cracking.
• It’s a flexible lattice made from woven glass-fibre strands offering incredible strength when embedded into base coat render.
• The render reinforcing fibreglass mesh is made out of alkaline resistant glass yarns and has been tested to DIN EN ISO 13934-1 tensile strength standards.
• Easy to install, by embedding it in to wet base coat render especially for large surface areas.
• Durable and Reliable.
• Light and easy to transport.
• Adaptable to uneven surfaces.
• Only simple tools required. (Scissors / Utility Knife).

The post Render Mesh appeared first on Eden Hot Lime Mortar.